Comando da chave [problema semi resolvido]

Black_Car

Black_Car

Boas a todos,
Estou com o seguinte problema e o qual nao consigo resolver porque nao sei o k é.

"então é o seguinte, as chaves da minha B6 deixaram de funcionar o comando nao abre nem fecha as portas, já experimentei as duas chaves, já coloquei pilhas novas nas duas chaves, fiz um scan com o vag e nao detecta qualquer erro relacionado com o fecho central" Preciso de ajuda para ver se consigo resolver o problema, pois alem do incomodo k é ter k abrir o carro com a chave na fechadura.............em termos de aspecto, digam de vossa justiça o k pensavam vcs ao ver uma maquina como uma argolas nao ter comando á distancia.
 
Last edited:
Re: Comando da chave

Gather ALL the remotes you would like to match. Insert one key in the ignition and turn it ON.
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Adaptation - 10]

Enter channel "01" (May be channel "21" in some Audi models).

[Read]

This will display the number of currently stored remotes in "Stored Value".

Enter your total number of keys up to a maximum of 4(including any existing keys) in "New Value"

[Test]

Verify that the number in "Test Value" is correct.

[Save]
Then press and hold (for at least one second) the UNLOCK button on the fob, at which time it will be learned. If you're programming more than one fob press and hold the UNLOCK button on the second fob for one second, press and hold the UNLOCK button on the third fob for one second, etc. You have a total of 15 seconds to do them all.
The car may give you some sort of acknowledgement as each key is learned (lights flash, horn beep, etc.)
If the above procedure does not work (neither Channel 01 nor Channel 21 are available), follow this procedure:
Insert a working (old) key in the ignition and turn to the ON position (do not start car).
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Meas. Blocks - 08]
Enter group "003" (may be group "007" in some vehicles)
[Go!]
The value in field 2 shows how many remotes have been matched and in which memory positions (for example, "0001" indicates 1 transmitter in position 1).
Lock the car from outside using the new, unmatched key in the driver-side door lock.
Press the UNLOCK button on the new key within 5 seconds often enough to reach next memory position (so, if the value in field 2 was 0001, you should press the new key's unlock button twice, to put the new key in memory position 2)..
The car may give you some sort of acknowledgement as the button is pressed (lights flash, horn beep, etc.)
Wait 5 seconds and press the unlock button on the new key to unlock the door.
Turn the ignition key to OFF and remove the old key.

Press LOCK and UNLOCK with the new key.
Insert the new key in the ignition and turn to the ON position (do not start car).
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Meas. Blocks - 08]
Enter group "003"
[Go!]
The value in field 2 should now indicate 0011 in the example used, showing the old key still matched in position 1 and the new key matched in position 2.

Make sure that new keys are always coded into free memory positions (where there is a zero in Group 003, field 2). If occupied positions (distinguishable by a "1") are used, the transmitter previously coded to this position will no longer work.
In some cases, it may be necessary to clear out existing matched remotes using the following procedure:
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Adaptation - 10]
Enter channel "00"
[Read]

[Save]
When the prompt asks if you are sure you want to save a value of 0 to Channel 00, click [Yes]
 
Re: Comando da chave

PEREIRA disse:
Gather ALL the remotes you would like to match. Insert one key in the ignition and turn it ON.
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Adaptation - 10]

Enter channel "01" (May be channel "21" in some Audi models).

[Read]

This will display the number of currently stored remotes in "Stored Value".

Enter your total number of keys up to a maximum of 4(including any existing keys) in "New Value"

[Test]

Verify that the number in "Test Value" is correct.

[Save]
Then press and hold (for at least one second) the UNLOCK button on the fob, at which time it will be learned. If you're programming more than one fob press and hold the UNLOCK button on the second fob for one second, press and hold the UNLOCK button on the third fob for one second, etc. You have a total of 15 seconds to do them all.
The car may give you some sort of acknowledgement as each key is learned (lights flash, horn beep, etc.)
If the above procedure does not work (neither Channel 01 nor Channel 21 are available), follow this procedure:
Insert a working (old) key in the ignition and turn to the ON position (do not start car).
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Meas. Blocks - 08]
Enter group "003" (may be group "007" in some vehicles)
[Go!]
The value in field 2 shows how many remotes have been matched and in which memory positions (for example, "0001" indicates 1 transmitter in position 1).
Lock the car from outside using the new, unmatched key in the driver-side door lock.
Press the UNLOCK button on the new key within 5 seconds often enough to reach next memory position (so, if the value in field 2 was 0001, you should press the new key's unlock button twice, to put the new key in memory position 2)..
The car may give you some sort of acknowledgement as the button is pressed (lights flash, horn beep, etc.)
Wait 5 seconds and press the unlock button on the new key to unlock the door.
Turn the ignition key to OFF and remove the old key.

Press LOCK and UNLOCK with the new key.
Insert the new key in the ignition and turn to the ON position (do not start car).
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Meas. Blocks - 08]
Enter group "003"
[Go!]
The value in field 2 should now indicate 0011 in the example used, showing the old key still matched in position 1 and the new key matched in position 2.

Make sure that new keys are always coded into free memory positions (where there is a zero in Group 003, field 2). If occupied positions (distinguishable by a "1") are used, the transmitter previously coded to this position will no longer work.
In some cases, it may be necessary to clear out existing matched remotes using the following procedure:
[Select]

[46 - Cent. Conv.] or [35 - Cent. Locking] (whichever is applicable to the car, as found here)
[Adaptation - 10]
Enter channel "00"
[Read]

[Save]
When the prompt asks if you are sure you want to save a value of 0 to Channel 00, click [Yes]
Clique para expandir...

Obrigado Pereira,
Tudo isto é muito bonito, mas alem de eu nao ter vag, nao pesco nada disto, será k me podes dar uma ajuda????
Vou manda PM
Abraço
 
Re: Comando da chave

Oi
insere uma das chaves para teste e dá à chave, sem ligar o carro...só a acender aas luzes e simbolos no quandrante.
com a chave assim, pressiona um dos botões do comando, durante uns segundos....desliga, tira a chave e experimenta...

Abraço
 
Re: Comando da chave

faithnomore disse:
Oi
insere uma das chaves para teste e dá à chave, sem ligar o carro...só a acender aas luzes e simbolos no quandrante.
com a chave assim, pressiona um dos botões do comando, durante uns segundos....desliga, tira a chave e experimenta...

Abraço
Clique para expandir...

s for apenas a memoria de posição isso pode dar....

mas como ele diz k não dá nenhuma..... :s

amanhã talvez já se descubra o gato... :p
 
Re: Comando da chave

faithnomore disse:
Oi
insere uma das chaves para teste e dá à chave, sem ligar o carro...só a acender aas luzes e simbolos no quandrante.
com a chave assim, pressiona um dos botões do comando, durante uns segundos....desliga, tira a chave e experimenta...

Abraço
Clique para expandir...

Obrigado pela ajuda, mas já experimentei e nao deu.
Abraço
 
Re: Comando da chave

Black....

se quiseres amanhã dá um toque depois da hora que te falei e vemos isso..
 
Re: Comando da chave

faithnomore disse:
Oi
insere uma das chaves para teste e dá à chave, sem ligar o carro...só a acender aas luzes e simbolos no quandrante.
com a chave assim, pressiona um dos botões do comando, durante uns segundos....desliga, tira a chave e experimenta...

Abraço
Clique para expandir...

faithnomore disse:
...eu experimentava outra vez....nem que fosse a testar 1 botão de cada vez...
Clique para expandir...

É o k me acontece várias vezes, e é este o procedimento k eu faço sempre, e sempre funcionou!! Tenta este processo, e carrega nos dois botões um de cada vez, depois desliga a chave e vê se funciona!!
 
Re: Comando da chave

comigo já aconteceu duas vezes e com ambas (duas) chaves ! meto as na ignição e já está ! mas alguém sabe a razão de se desprogramarem ? no ínicio fartei me de gastar dinheiro em pilhas e depois vi que não era das pilhas !
 
Re: Comando da chave

Comigo farta-se de acontecer isso. Se meter a chave na ignição, rodar para posição ON e carregar num dos botões a chave fica programada.

É claro que já desisti de o fazer pois tenho o comando do alarme que uso para abrir e fechar o carro.
 
O problema está semi resolvido, pois com a ajuda de um amigo do Forum e o seu vagcom, conseguimos formatar uma das chaves, só uma a outra nao sabemos muito bem porque nao se conseguiu, mesmo comprando uma pilha nova nao deu, mas pelo uma já funciona (pelo menos para já).
 
You must log in or register to reply here.
Back
Top